EDM Wire Cutting Machine Vertical Auxiliary Molybdenum Wire Vertical Corrector

Description

Molybdenum wire vertical corrector Vertical auxiliary tool for wire cutting machine calibration. Use and Adaptation This product is mainly used in wire electric discharge machine tools as the vertical correction of electrode wire. This corrector is especially important for wire cutting machine tools with an inclined cutting function and adjustable wire frame span. This product is also suitable for vertical correction of tool electrodes of EDM (perforation) processing machine tools and vertical correction of workpieces by machining, clamps, etc. Specific operating steps and precautions 1. For vertical correction of wire electrode of WEDM 2. Battery replacement 3.Precautions Package includes: 1 * corrector (70 * 70 * 68mm)
Store category
Sign Up Now !
You may also like
EDM Wire Drilling Cutter Molybdenum Wire Vertical Corrector Vertical Auxiliary
Product Description
Molybdenum wire vertical corrector
Vertical auxiliary tool for wire cutting machine calibration.
I. Use and Adaptation
This product is mainly used in wire electric discharge machine tools as the vertical correction of electrode wire. This corrector is especially important for wire cutting machine tools with an inclined cutting function and adjustable wire frame span.
This product is also suitable for vertical correction of tool electrodes of EDM (perforation) processing machine tools and vertical correction of workpieces by machining, clamps, etc.
Brief introduction and characteristics of working principle
DF55-J50A vertical corrector is a long life, low power consumption, intuitive and convenient detection tool, using light-emitting diode display, a photoelectric detection tool with internal power supply, the circuit is closed when the measuring head contacts the measured conductive object The light emitting diode is turned on and emits light. According to the states of the upper and lower light emitting diodes, the vertical condition of the device under test can be conveniently and intuitively detected. This corrector is suitable for various types of wire electric discharge machine tools.
When the measuring head of the calibrator contacts the object to be measured, the flashing state of the light emitting diode transitions to the on or off state, and the contact distance between them is between 1.5-2 microns. Therefore, the measurement force of this corrector is very small, and the sensitivity is high, which brings high accuracy for vertical correction.
Because this corrector uses a natural marble support, the support does not deform, and the reference surface and measuring head are carefully studied, and the support is made of hard material. Therefore, the accuracy of this corrector is very good.
In addition to the natural marble support, the measuring head is made of stainless steel, and the whole seal is sealed, so its corrosion resistance and durability are very good.
Third, use
First, familiarize yourself with the structure and working principle of this corrector. Each measuring head has two measuring surfaces a, b. We let the two measuring surfaces of the upper two measuring heads be a and b, and the two measuring surfaces corresponding to ab be a 'and b'.
The a-a 'measuring plane is parallel in space and perpendicular to the b-b' measuring plane. The leads between each point on the a plane and the corresponding points on the a 'plane are perpendicular to the bottom plane of the corrector support, b -b 'Same. When the measured object (such as the electrode wire) is in contact with the a and a 'surfaces, the upper and lower display lights are on at the same time. When only a or a' is touched, only the upper or lower display lights are on;
From the point of view of surveying, the smaller the measuring force between the measurement and the object to be measured is, the better. Therefore, when using the corrector, you should try to touch the object to be measured slowly and lightly. When the indicator light flickers, observe whether the upper and lower indicator lights are at the same time. Flashes or lights at the same time. If it flashes at the same time or both light and dark, it means that the device under test is perpendicular to the bottom plane of the corrector support.
Fourth, specific operating steps and precautions
1. For vertical correction of wire electrode of WEDM:
① Cut off the processing power and stop wire feeding.
② Tighten the electrode wire and wipe clean the tested surface.
③ Wipe the working surface (fixture plane) and the bottom of the corrector separately
④ Place the calibrator on the work surface, and make the two measuring heads a and b of the measuring head parallel to the x and y coordinate axis directions, respectively. The measuring head should protrude from the workpiece fixture so that the measuring head and the electrode wire are moved when the table is moved contact.
⑤ Clip the crocodile clip on the conductive block of the electrode wire, and insert the plug into the socket on the corrector.
⑥ According to the working principle of this product, correct the detection electrode wire in the x and y coordinate directions, corresponding a-a ', b-b'
(Measurement surface) The verticality of the working installation plane, adjust the guide wheel bearing or the guide or the wire frame to correct the verticality.
If you want to accurately correct the vertical, you can repeatedly check and adjust until the upper and lower display lights flash at the same time.
2. Battery replacement:
When the brightness of the display lamp is weakened to prevent observation, it indicates that the power supply voltage is insufficient. If you want to replace the battery (9V laminated battery), you can use a blade to glue the upper cover of the corrector and the silicone rubber adhesive glued to the support.
3.Precautions
① Pay attention to the anti-shattering and anti-cracking of the marble support during use and transportation, and take proper measures.
② Avoid scratching the bottom surface of the support and the measuring surface of the measuring head during use.
③ When not in use, it should be stored in the box for future use
Package includes:
1 * corrector (70 * 70 * 68mm)
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
We accept PayPal payment only
Payment must be received within 7 days after order is made.
Fees such as import duties, taxes are not included in the item price or shipping costs. These charges are the buyer's responsibility.
Delivery details
Shipping:
The item will be shipped from our US warehouse to United States, which is more faster than from aboard.
2-9 working days to: USA
Terms of sales
We maintain high standards of excellence and strive for hundred percent customer satisfaction. Feedback is very important to us. We hope that you contact us immediately before you give neutral or negative feedback, so that we can address your concerns. It is impossible to address issues if we do not know about them!
About us
Your satis
faction is our ultimate goal. We work hard to earn your trust and future business. Our certified technicians have tested each item before shipping. The unit comes with 1 year limited warranty on all manufacturing defects.
a) If you receive a defective item, you may return it or ask for a discount. Please contact us within 14 days after you receive the package.
b) What you returned must be intact and in its original packaging as re? u. Customer is responsible for shipping costs of the returned item.
c) We will cover the cost of shipping back t with the shipping rate indicated in the registration page. We will send you a new unit or refund the full payment you paid.
Thank you.
Contact us
Business Hour
Business Hour: Monday To Friday: 8:30 AM to 5:00 PM (Beijing China time)
Due to time zones, our reply to your questions may not be immediately. But within above working time, we will reply your email within 24 hours. If it's non-workdays, please kindly be patient and wait till Monday.
Please contact us with ebay message.
Please feel free to contact us if you have any questions.
: Monday To Friday: 8:30 AM to 5:00 PM (Beijing China time)
Due to time zones, our reply to your questions may not be immediately. But within above working time, we will reply your email within 24 hours. If it's non-workdays, please kindly be patient and wait till Monday.
Please contact us with ebay message.
Please feel free to contact us if you have any questions.
Feedback
On May-25-21 at 01:42:11 PDT, seller added the following information: